Fig: OSPF Protocol Configuration
OSPF
Router 0 Configureation
Router>enable
Router#configure
terminal
Enter
configuration commands, one per line. End with CNTL/Z.
Router(config)#interface
FastEthernet0/0
Router(config-if)#ip
address 192.168.1.1 255.255.255.0
Router(config-if)#no
shutdown
Router(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface
Serial2/0
Router(config-if)#ip
address 10.10.0.2 255.0.0.0
Router(config-if)#clock
rate 64000
Router(config-if)#
Router(config-if)#exit
Router(config)#interface
Serial3/0
Router(config-if)#ip
address 12.12.0.2 255.0.0.0
Router(config-if)#clock
rate 64000
Router(config-if)#no
shutdown
%LINK-5-CHANGED:
Interface Serial3/0, changed state to down
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial3/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#interface
Serial2/0
Router(config-if)#no
shutdown
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
exit
Router(config)#router
ospf 1
Router(config-router)#network
192.168.1.0 0.0.0.255 area 0
Router(config-router)#network
10.0.0.0 0.255.255.255 area 0
Router(config-router)#network
12.0.0.0 0.255.255.255 area 0
Router(config-router)#exi
Router(config)#exit
Router#
%SYS-5-CONFIG_I:
Configured from console by console
00:08:39:
%OSPF-5-ADJCHG: Process 1, Nbr 11.11.0.2 on Serial2/0 from LOADING to
FULL, Loading Done
00:09:57:
%OSPF-5-ADJCHG: Process 1, Nbr 192.168.2.1 on Serial3/0 from LOADING
to FULL, Loading Done
OSPF
Router 1 configuration
outer>enable
Router#configure
terminal
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#interface
Serial2/0
Router(config-if)#ip
address 10.10.0.3 255.0.0.0
Router(config-if)#no
shutdown
%LINK-5-CHANGED:
Interface Serial2/0, changed state to down
Router(config-if)#
Router(config-if)#exit
Router(config)#interface
Serial3/0
Router(config-if)#ip
address 11.11.0.2 255.0.0.0
Router(config-if)#clock
rate 64000
Router(config-if)#no
shutdown
%LINK-5-CHANGED:
Interface Serial3/0, changed state to down
Router(config-if)#
Router(config-if)#exit
Router(config)#interface
Serial2/0
Router(config-if)#
Router(config-if)#exit
Router(config)#interface
Serial3/0
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial3/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#interface
Serial2/0
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
exit
Router(config)#router
ospf 1
Router(config-router)#network
10.0.0.0 0.255.255.255 area 0
Router(config-router)#network
10.0.0.0 0.255.255.255 area 0
00:08:37:
%OSPF-5-ADJCHG: Process 1, Nbr 192.168.1.1 on Serial2/0 from LOADING
to FULL, Loading Done
Router(config-router)#network
11.0.0.0 0.255.255.255 area 0
Router(config-router)#exit
Router(config)#
00:09:38:
%OSPF-5-ADJCHG: Process 1, Nbr 192.168.2.1 on Serial3/0 from LOADING
to FULL, Loading Done
OSPF
Router 2 configuration
Router>enable
Router#configure
terminal
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#interface
FastEthernet0/0
Router(config-if)#ip
address 192.168.2.1 255.255.255.0
Router(config-if)#no
shutdown
Router(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface
Serial2/0
Router(config-if)#ip
address 11.11.0.3 255.0.0.0
Router(config-if)#no
shutdown
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#interface
Serial3/0
Router(config-if)#
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial2/0, changed state to up
ip address 12.12.0.3
255.0.0.0
Router(config-if)#no
shutdown
Router(config-if)#
%LINK-5-CHANGED:
Interface Serial3/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Serial3/0, changed state to up
exit
Router(config)#router
ospf 1
Router(config-router)#network
192.168.2.0 0.0.0.255 area 0
Router(config-router)#network
11.0.0.0 0.255.255.255 area 0
Router(config-router)#network
11.0.0.0 0.255.255.255 area 0
00:09:36:
%OSPF-5-ADJCHG: Process 1, Nbr 11.11.0.2 on Serial2/0 from LOADING to
FULL, Loading Done
Router(config-router)#network
12.0.0.0 0.255.255.255 area 0
Router(config-router)#exit
Router(config)#
00:09:53:
%OSPF-5-ADJCHG: Process 1, Nbr 192.168.1.1 on Serial3/0 from LOADING
to FULL, Loading Done
Hey, you there! I go through your whole content. It was amazingly written and i found it really useful for me...
ReplyDeleteplease give your precious time to visit my links given below. Buy healthy and delicious food from us.
Web Design Fort Myers
SEO Naples
SEO Fort Myers
Hello, I go through your whole content. It was amazingly written and i found it really useful for me...
ReplyDeleteplease give your precious time to visit my links given below. I want your attention on these topics too.
Diagnostic Software
Obd Diagnostic Interface
Heavy Duty Scanner
Hey! please stop scrolling now. I love your content it's very useful and I want your 1 minute attention for my amazing products. We provide Intelligent switch and more European socket along with these more items:
ReplyDeleteWall switch manufacturer
Switch socket manufacturer
Wall switch factory
Socket factory
I must say you gonna love them. please have a look once on our official website too